Whether you need a single electrical outlet added to a bedroom or a full room rewired with switched outlets and GFCI protection, we handle the entire process. Here is what our customers ask for most often.
New outlet installation covers mounting a receptacle in an existing or new electrical box, running wire from the nearest circuit, and connecting hot wires to brass screws and neutral to silver screws with a bare copper ground wire secured to the green grounding screw. We verify the corresponding circuit breaker is properly rated, test every connection with a voltage tester, and install a clean cover plate. This service fits homeowners who need additional power access in kitchens, bedrooms, living areas, or home offices. The result is a fully functional outlet receptacle with proper grounding and GFCI protection where required by code.
A switched outlet lets you control lights or lamps from a wall switch instead of reaching behind furniture. We install both half-switched and fully switched configurations. For a half-switched (half-hot) outlet, we run 14/3 or 12/3 cable between the switch box and receptacle box. The black wire provides constant power to one half of the outlet, and the red wire acts as the switch leg for the other half. We break the hot side tab between the brass terminals so each half operates independently while leaving the neutral side tab intact. The result is one half of your outlet always on for chargers or appliances, and the other half controlled by your light switch. For fully switched outlets, both halves respond to the off switch position, which works well when you want a single point of control for floor lamps.
Electrical work must comply with local and national codes to ensure safety and legality, and installing or replacing an outlet switch in a home requires attention to local electrical standards. We handle all of that so you don't have to think about it.
Outlets in kitchens, bathrooms, garages, and outdoor areas must have Ground Fault Circuit Interrupter (GFCI) protection. GFCI protection is necessary in damp areas to prevent electrocution. If your home was built before the mid-1990s, many of these locations may still have standard outlets without ground fault protection. We replace old receptacles with GFCI-rated devices, wire them correctly, and test the trip-and-reset function before we leave. Oklahoma City enforces compliance with the National Electrical Code (NEC), and Oklahoma City adopted the 2023 NEC effective September 14, 2024, transitioning from the 2017 NEC. That means GFCI requirements are broader now than when many OKC homes were originally wired.
USB outlets combine standard plug receptacles with built-in USB-A or USB-C charging ports, eliminating bulky adapter blocks. We install these in bedrooms, kitchens, living rooms, and home offices where device charging happens daily. The installation process is similar to a standard outlet swap, but we verify your circuit can support the additional draw and that all connections at the screw terminal points are tight and secure.
We evaluate your electrical panel capacity, check your breaker box for available circuits, and inspect existing wiring. If we find frayed insulation or corrosion, we flag it before work begins. Ensure wiring integrity by inspecting for frayed insulation or corrosion before proceeding. You receive an upfront quote covering labor, materials, and permit fees.
Our licensed electricians turn off the power at the breaker before starting work and use a non contact voltage tester to confirm no live electrical current is present. We remove the existing outlet cover and unscrew the old receptacle if replacing. For new installations, we cut in the box, run properly gauged cable, and make every connection to code. We use correct wire gauge corresponding to the amperage of the circuit. Hot wires connect to brass screws, neutral wires connect to silver terminal screws, and ground wires attach to the green grounding screw. When a white wire is used as a switched hot in a switch loop, we mark the white wire connected to the switch with black tape per NEC 200.7(C). We carefully tuck all wires back into the box, secure exposed terminal screws with electrical tape to prevent contact, and mount everything with proper mounting screws. A 4-in-1 screwdriver is essential for outlet installation, and wire strippers are needed to prepare electrical wires properly.
We clean up completely and test every connection for safety. A circuit tracer helps identify circuit breakers efficiently when multiple circuits sharing a box should be treated with caution during electrical work.
We test the outlet after installation to ensure proper wiring, then restore power at the correct breaker. You get a fully functional installation backed by our satisfaction guarantee. For jobs requiring a city permit, we schedule the inspection with OKC Building & Trade Permits and handle any follow-up. We also walk you through maintenance basics: how to test GFCI outlets monthly, when to call us back, and what to watch for with your new outlets.
We keep the upgrade process transparent from your first call to your final inspection. Most homeowners are surprised at how little disruption there actually is.
A licensed electrician comes to your home, evaluates your current panel, reviews your wiring, and performs a load calculation. You'll get a clear explanation of what needs to happen, a written estimate with no hidden fees, and a timeline. We also walk you through financing options and the permit requirements for your project. Oklahoma City requires an electrical trade permit for any panel replacement or upgrade, and permits should be obtained before starting any work. We handle that paperwork for you.
A typical electrical panel upgrade takes one to three days. Day 1 involves inspection and disconnection of the old panel. Day 2 is for installing and wiring the new panel. Day 3 includes final testing and inspection by a licensed electrician. Power will be turned off during the upgrade process, and we schedule the work to keep that downtime as short as possible. For a standard 100 to 200 amp replacement without additional electrical work, expect 4 to 8 hours of active installation time. If we're relocating the panel or running new wire for additional circuits, it may take a full day or more.
All work follows the current adopted electrical code in Oklahoma City, which is the 2017 National Electrical Code (NEC). Electrical work in Oklahoma City must be performed by licensed electrical contractors, and every Comfort Wave electrician meets that requirement.
Once the new electrical panel is installed, we test every circuit breaker, verify grounding and bonding, and confirm safe operation across your home's electrical system. Electrical inspections are required after panel upgrades to ensure compliance with safety codes, and we coordinate that inspection with the city.
We walk you through your upgraded electric panel so you know what each breaker controls. You'll receive warranty documentation and know exactly who to call if you ever have a question.
We show you the price before we start. Our upfront pricing means no surprises when the job wraps up. Every installation uses professional-grade components rated for the correct amperage of the circuit, which means they hold up longer than the budget devices you find at big-box stores. And because our electricians pull permits and follow the National Electrical Code (NEC), your work passes inspection on the first visit.
Comfort Wave serves homeowners throughout the Oklahoma City metro area, including:
Older homes in areas like Edmond and Norman with plaster walls can present challenges when fishing wire through walls. We have the tools and experience to handle those situations without unnecessary wall damage.
A standard outlet installation in OKC runs between $102 and $423, with most jobs landing around $212. That includes the receptacle, electrical box, wiring from the nearest circuit, cover plate, and grounding verification. GFCI outlet upgrades typically cost $130 to $303 depending on the location and existing wiring. Factors that affect pricing include circuit distance from your breaker box, wall material (drywall is easier than plaster or concrete), and whether your existing wiring needs upgrades. Permits are needed for new electrical circuits and significant alterations in Oklahoma City, and permit fees in OKC run between $100 and $200 for typical electrical permit work. We include all of this in our upfront quote.
Electrical work in Oklahoma City typically requires a licensed electrical contractor and a permit. Any time you alter wiring, add a new outlet, or change electrical systems, the OKC Building & Trade Permits office requires a residential electrical permit. Comfort Wave pulls the permit, schedules the inspection, and makes sure everything passes. Working without a permit can lead to fines and complications during home resale.
A single outlet or switch installation typically takes 1 to 2 hours, including wiring, testing, and cleanup. If we need to fish wire through walls or run cable from a distant panel, it may take longer. We offer same-day service for most standard installations, so if you call in the morning, we can often have your new outlet working by afternoon.
Yes. Many OKC homes built in the 1970s and 1980s have wiring that predates current NEC requirements. Common issues include missing ground wires, no neutral wire in switch boxes, outdated two-prong outlets, and circuits without GFCI or AFCI protection. We assess the existing wiring condition and recommend the appropriate upgrades. Some older homes have aluminum wiring or outdated wiring methods that require careful attention and specific connection techniques. Tamper-Resistant (TR) receptacles are required for new or replaced residential outlets, so any outlet we install meets that standard. Grounding reduces the risk of electrical shock, and tamper-resistant receptacles prevent children from inserting objects, making these upgrades worthwhile for both safety and code compliance.
Reversed hot and neutral wires can create shock risks, which is why we verify every connection with a tester. Secure connections and grounding are necessary to prevent electrical faults. DIY electrical work on older systems without proper knowledge of three way switches, multi-wire branch circuits, or proper wire identification creates real danger. If you are not sure about the wiring in your home, professional help from a licensed electrician is the safest path. Turn off the breaker before any electrical work, and test every circuit to ensure it's de-energized before working. These are not suggestions; they are requirements for safe electrical projects.
Safe, code-compliant outlet and switch installation protects your home and your family. Every connection matters, from the tight connection at each brass terminal to the ground wire at the green grounding screw. Let Comfort Wave handle your next electrical project the right way.
Call today for a free estimate. Same-day service available across the Oklahoma City metro.
A new heating and cooling system is a significant investment. At Comfort Wave Home Services, we safeguard your investment with our Wave Club Maintenance Plan.
We're not just another home services company. We're a team of dedicated experts committed to your comfort, safety, and peace of mind.
Are you dedicated to making a difference in the lives of customers and your community? Come join our team at Comfort Wave Home Services today!